Description
Price: 198.54 - 162.81
Good News: We have warehouse in some countries, check as below
Package include:
1)1 set GRBL 3018 CNC Laser machine kit (without laser)
or
2)1 set GRBL 3018 Pro CNC Laser machine kit (without laser)
or
3)1 set GRBL 3018 Pro Max CNC Laser machine kit (without laser)
10 x 20° 0.1mm drill bits
The machine for a full set of spare parts, shall be installed by the
buyers, the package include the U Disk , with detailed user manual and
free software,buyers don’t need to worry about machine assembly.
Introduction:
body
used profiles and plastic, small size, light weight, USB interface,
GRBL control system, learning, entry preferred. can use carving knife,
but also can use laser engraving.
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
Specification:
Laser: 500mw 405nm,12v / 2500mw 450nm,12v / 5500mw 450nm,12v.
Drill bits: tip 0.1mm ,20 degree , diameter3.175mm.the package includes 10p
Support System: Windows XP / Win 7 / Win 8 / Win 10 / Linux
Software: GRBL controller
Power supply: 24V 5.6A
Step motor: Fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/M
Spindle Chuck: normal
Spindle: 775 spindle motor (12-36V) 24V: 10000r/min
Frame size: 40 x 33 x 24 cm
Working area: 30 x 18 x 4.5 cm
Introduction:
body
used profiles and plastic, small size, light weight, USB interface,
GRBL control system, learning, entry preferred. can use carving knife,
but also can use laser engraving.
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
Specification:
Laser: 500mw 405nm,12v / 2500mw 450nm,12v / 5500mw 450nm,12v.
Drill bits: tip 0.1mm ,20 degree , diameter3.175mm.the package includes 10p
Support System: Windows XP / Win 7 / Win 8 / Win 10 / Linux
Software: GRBL controller
Power supply: 24V 5.6A
Step motor: Fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/M
Spindle Chuck: normal
Spindle: 775 spindle motor (12-36V) 24V: 10000r/min
Frame size: 40 x 33 x 24 cm
Working area: 30 x 18 x 4.5 cm
2. GRBL 1.1F, USB port cnc engraving machine control board, 3 axis control
Grbl control board specification:
Connection: USB (USB-CH340)
Software: GRBL controller, UniversalGcodeSender
Input voltage: 12-36V
Master chip: atmel 328P (arduino nano)
Stepper motor driver: A4988
Spindle drive chip: MOSFET (recommendation 12~36V, current: within 10A)
Spindle PWM speed: Support
Support
stepper motor: 12V, maximum current of 2A or less is recommended within
1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Interface: 5.5-2.5mm DC interface
Advantage:
1. Add the outer casing: mainly for the bare board of the control board, short circuit problem during use
2.Add the power button switch (this switch is the power supply control
signal, there is no large current passing through the switch, do not
worry about the switch size)
3.Cancel the drive module, integrated imported stepper motor drive, with
short circuit protection, no need to worry about module damage. And
integrated heat dissipation aluminum alloy
4. Add the fan to force heat dissipation.
5. Add offline recognition to insert offline modules and computers at the same time.
6. Offlinewill automatically identify if there is computer control.
7. Enhanced spindle drive. Can support 20,000 rpm spindle. Support for larger power spindles
8. Improved power interface: original plastic interface changed to full metal shielded interface
9.Improved USB interface: The original USB interface is patch soldering,
Transport collision and improper use, easy to drop, now changed to
plug-in, very strong
10.The spindle drive increases the optocoupler isolation, which makes the
Control board generates less heat, and the spindle speed adjustment is
more linear and safer.
11. The stepper motor drive increases the self-recovery fuse. When a short
circuit or fault occurs, the power supply is cut off and the fault
indicator light is displayed.
12. The 12V step-down increases the self-recovery fuse. When a short circuit occurs, the power can be cut off
off in time to avoid damage.
13. Optimize layout, control area and drive area separation, run more stable"
Main application:
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
Can be used for carving, cutting. Can cut wood
Transparent and white material can not be cut.
Laser focus adjustable
2. GRBL 1.1F, USB port cnc engraving machine control board, 3 axis control
Grbl control board specification:
Connection: USB (USB-CH340)
Software: GRBL controller, UniversalGcodeSender
Input voltage: 12-36V
Master chip: atmel 328P (arduino nano)
Stepper motor driver: A4988
Spindle drive chip: MOSFET (recommendation 12~36V, current: within 10A)
Spindle PWM speed: Support
Support
stepper motor: 12V, maximum current of 2A or less is recommended within
1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Interface: 5.5-2.5mm DC interface
1. Add the outer casing: mainly for the bare board of the control board, short circuit problem during use
2.Add the power button switch (this switch is the power supply control
signal, there is no large current passing through the switch, do not
worry about the switch size)
3.Cancel the drive module, integrated imported stepper motor drive, with
short circuit protection, no need to worry about module damage. And
integrated heat dissipation aluminum alloy
4. Add the fan to force heat dissipation.
5. Add offline recognition to insert offline modules and computers at the same time.
6. Offlinewill automatically identify if there is computer control.
7. Enhanced spindle drive. Can support 20,000 rpm spindle. Support for larger power spindles
8. Improved power interface: original plastic interface changed to full metal shielded interface
9.Improved USB interface: The original USB interface is patch soldering,
Transport collision and improper use, easy to drop, now changed to
plug-in, very strong
10.The spindle drive increases the optocoupler isolation, which makes the
Control board generates less heat, and the spindle speed adjustment is
more linear and safer.
11. The stepper motor drive increases the self-recovery fuse. When a short
circuit or fault occurs, the power supply is cut off and the fault
indicator light is displayed.
12. The 12V step-down increases the self-recovery fuse. When a short circuit occurs, the power can be cut off
off in time to avoid damage.
13. Optimize layout, control area and drive area separation, run more stable"
Main application:
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
FAQ:
1 Q: Does this machine need to be assembled when I received it?
A: This machine comes as a kit. You need to assemble it yourself. All tools and parts are included
in the kit.
2 Q: How to assemble the kit?
A: We’ll provide whole assemble and operating manual, please share your email address, then we’ll send to you.
3 Q: Are there software and instructions can I get it?
A: You can get the software in a USB disk with machine.
4 Q: And what image format the software supports? Engraving Mode?
A: Supported Image Format: jpg, bmp, svg, G-code
Supported Engrave Mode: Photo, Word, Scan, Outline, Pixel Laser Engraving
5 Q: What type of computer system can run its software?
A: The software only support the Windows XP/7/8/10.
6 Q: What’s the laser’s lifetime?
A: The laser module has over 6,000 hours lifetime.
7 Q: What material can it engrave?
A: Wood, bamboo, plastic, paper, leather, rubber, MDF.
8 Q: What material can it cut?
A: wood, paper, thin leather.
9 Q:Can I use it to cut or engrave on metal?
A: It can not engrave or cut on any metal.
10 Q: Can I regulate the laser power or is the laser power adjustable?
A: Sorry that the fixed laser power is not adjustable, but the engraving speed is adjustable.
11 Q: How long can the machine work continuously?
A: It can work continuously about 45 minutes, after the laser mold cools
down (about half an hour), then start working again. Long time work
continuously with shorten the laser module lifetime.
12 Q: My laser doesn’t work, what should I do?
If the machine does not work, it might because:
A The wire connection is wrong. Please check the connection like the picture shown.
B Your computer could not support the software. Please use Win XP 7/8/10 to check it.
C Software problem.Please check whether wires are inserted right. And then check your data setting.
D The kit misses some accessories. Please compare with the instruction and tell us, we will solve it once you send us the email.
E Laser module/ driver board/ power supply is broken.
Please check which part is the main problem, and then send us a video to prove it.
Or you can send us a video about your software setting, working laser and driver board. We will analyze it and give you a solution.
Friendly Note:
Due to the different wattage of the laser head, the engraving material
range, engraving speed, depth, etc. are different. The greater the
power, the faster the speed
3W-5.5W laser:
1. Can carve wood, paper, plastic, leather, bamboo, bones, teeth, etc.
2. Can’t carve metal
7W-10W laser:
1.Can carve Wood, paper, plastic, leather, bamboo, bones, teeth, acrylic and other materials that can be burned by fire.
2. Can carve 304 201 pure color stainless steel, painted metal (except
stainless steel, other pure metal with primary color smooth surface
cannot be carved)
1 Q: Does this machine need to be assembled when I received it?
A: This machine comes as a kit. You need to assemble it yourself. All tools and parts are included
in the kit.
2 Q: How to assemble the kit?
A: We’ll provide whole assemble and operating manual, please share your email address, then we’ll send to you.
3 Q: Are there software and instructions can I get it?
A: You can get the software in a USB disk with machine.
4 Q: And what image format the software supports? Engraving Mode?
A: Supported Image Format: jpg, bmp, svg, G-code
Supported Engrave Mode: Photo, Word, Scan, Outline, Pixel Laser Engraving
5 Q: What type of computer system can run its software?
A: The software only support the Windows XP/7/8/10.
6 Q: What’s the laser’s lifetime?
A: The laser module has over 6,000 hours lifetime.
7 Q: What material can it engrave?
A: Wood, bamboo, plastic, paper, leather, rubber, MDF.
8 Q: What material can it cut?
A: wood, paper, thin leather.
9 Q:Can I use it to cut or engrave on metal?
A: It can not engrave or cut on any metal.
10 Q: Can I regulate the laser power or is the laser power adjustable?
A: Sorry that the fixed laser power is not adjustable, but the engraving speed is adjustable.
11 Q: How long can the machine work continuously?
A: It can work continuously about 45 minutes, after the laser mold cools
down (about half an hour), then start working again. Long time work
continuously with shorten the laser module lifetime.
12 Q: My laser doesn’t work, what should I do?
If the machine does not work, it might because:
A The wire connection is wrong. Please check the connection like the picture shown.
B Your computer could not support the software. Please use Win XP 7/8/10 to check it.
C Software problem.Please check whether wires are inserted right. And then check your data setting.
D The kit misses some accessories. Please compare with the instruction and tell us, we will solve it once you send us the email.
E Laser module/ driver board/ power supply is broken.
Please check which part is the main problem, and then send us a video to prove it.
Or you can send us a video about your software setting, working laser and driver board. We will analyze it and give you a solution.
Due to the different wattage of the laser head, the engraving material
range, engraving speed, depth, etc. are different. The greater the
power, the faster the speed
3W-5.5W laser:
1. Can carve wood, paper, plastic, leather, bamboo, bones, teeth, etc.
2. Can’t carve metal
7W-10W laser:
1.Can carve Wood, paper, plastic, leather, bamboo, bones, teeth, acrylic and other materials that can be burned by fire.
2. Can carve 304 201 pure color stainless steel, painted metal (except
stainless steel, other pure metal with primary color smooth surface
cannot be carved)
Reviews
There are no reviews yet.